Yaskawa SGDV-170D11A MECHATROLINK-II Commands Manual SGDV-170D11A USER'S MANUAL

Sigma -V series servo motor SGMJV.
Rated output: 0.75KW (750W).
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value (standard).
Design sequence: standard.
Shaft end: with two side plane seat (optional).
Optional: with oil seal.
Medium inertia.
Instantaneous maximum torque (rating 350%) SGDV-170D11A MECHATROLINK-II Commands Manual SGDV-170D11A USER'S MANUAL.
Equipped with a high resolution serial encoder (13/20 bit) SGDV-170D11A
Max speed up to 6000r/min.
Variety is complete (50 ~ 750W, with hold brake).
Use example:
Semiconductor manufacturing equipment,
Placement machine,
Punch printed circuit board,
Robot，
Handling machinery，
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above SGDV-170D11A MECHATROLINK-II Commands Manual SGDV-170D11A USER'S MANUAL.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation SGDV-170D11A MECHATROLINK-II Commands Manual SGDV-170D11A USER'S MANUAL. Servo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 4.4kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit relative value.
Design sequence: high precision machine tool.
Shaft end: taper 1\/10, with parallel key.
Optional parts: with oil seal, DC24V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlHigh performance, use the best type of servo unit (purpose type).
Maximum applicable motor capacity: 0.1kw.
Power supply voltage: single phase AC100V.
Interface: analog voltage, pulse sequence type (rotary servo motor).
Design sequence: B.
Hardware specifications: paint.
Function: to support the absolute value of the system.
Use the best type of sigma -V-FT series
According to different uses, there are 5 equipped with a convenient function of the servo unit models.
FT001 (vibration suppression function to upgrade specifications): by strengthening the vibration suppression function, shorten the positioning time.
FT003 (pressure feedback function): high precision pressure control, to promote the high performance of the device.
FT005 (support for rotary table purposes): with the rotation of the coordinate function and fixed point through the output function, can be smooth and high-precision control of rotary table SGDV-170D11A MECHATROLINK-II Commands Manual SGDV-170D11A USER'S MANUAL.
FT006 (fixed point through the output function): no need to pass through the upper device can bee set through the output (Chu Fa) SGDV-170D11A MECHATROLINK-II Commands Manual SGDV-170D11A USER'S MANUAL.
FT008 (absolute value system support): the absolute value of the system can be constructed by any upper controller.