Yaskawa SGMGV-1AD3C2B Setup Rotational Motor Manual SGMGV-1AD3C2B USER'S MANUAL

Large capacity SGMVV type servo motor.
Rated output: 30KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit delta.
Rated speed: 1500r\/min.
The main mechanical structure: support mounting type, straight shaft (with keyway and screw).
Optional parts: do not buy pieces.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties SGMGV-1AD3C2B Setup Rotational Motor Manual SGMGV-1AD3C2B USER'S MANUAL SGMGV-1AD3C2B
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenHigh performance, use the best type of servo unit (purpose type) SGMGV-1AD3C2B Setup Rotational Motor Manual SGMGV-1AD3C2B USER'S MANUAL.
Maximum applicable motor capacity: 6.0kw.
Power supply voltage: three phase AC400V.
Interface: MECHATROLINK-III communication command type (rotary servo motor).
Design sequence: A.
Hardware specification: rack mounting type.
Function: fixed point through output function SGMGV-1AD3C2B Setup Rotational Motor Manual SGMGV-1AD3C2B USER'S MANUAL.
Use the best type of sigma -V-FT series
According to different uses, there are 5 equipped with a convenient function of the servo unit models.
FT001 (vibration suppression function to upgrade specifications): by strengthening the vibration suppression function, shorten the positioning time.
FT003 (pressure feedback function): high precision pressure control, to promote the high performance of the device.
FT005 (support for rotary table purposes): with the rotation of the coordinate function and fixed point through the output function, can be smooth and high-precision control of rotary table.
FT006 (fixed point through the output function): no need to pass through the upper device can be set through the output (Chu Fa).
FT008 (absolute value system support): the absolute value of the system can be constructed by any upper controller. Sigma -V series servo motor SGMSV.
Rated output: 4.0kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value type (standard).
Design sequence: standard.
Shaft end: straight shaft, without keyway (standard).
Optional: with hold brake (DC90V).
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC11500V 1 minutes (200V), AC1800V 1 minutes (400V) SGMGV-1AD3C2B Setup Rotational Motor Manual SGMGV-1AD3C2B USER'S MANUAL.
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) SGMGV-1AD3C2B Setup Rotational Motor Manual SGMGV-1AD3C2B USER'S MANUAL.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation