Yaskawa SGMGV-1ED3C2D Setup Rotational Motor Manual SGMGV-1ED3C2D USER'S MANUAL

Sigma -V series servo motor SGMAV.
Rated output: 0.75KW (750W).
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: with two side plane seat (optional).
Optional: with oil seal.
Super power rate.
Small capacity.
Ultra low inertia
Instantaneous maximum torque (rating 300%) SGMGV-1ED3C2D Setup Rotational Motor Manual SGMGV-1ED3C2D USER'S MANUAL SGMGV-1ED3C2D
Equipped with a high resolution serial encoder (20 bit).
Max speed up to 6000r\/min.
Variety is complete (50W ~ 1.0kw, with hold brake).
Use example:
Semiconductor manufacturing equipment,
Placement machine,
Punch printed circuit board,
Robot，
Handling machinery，
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above SGMGV-1ED3C2D Setup Rotational Motor Manual SGMGV-1ED3C2D USER'S MANUAL.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection SGMGV-1ED3C2D Setup Rotational Motor Manual SGMGV-1ED3C2D USER'S MANUAL.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationLarge capacity SGMVV type servo motor.
Rated output: 45KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit absolute value type.
Rated speed: 1500r\/min.
The main mechanical structure: flange type, straight shaft (with keyway and screw).
Optional parts: do not buy pieces.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenNo speed reducer in inertia, high speed servo motor type SGM7J (rated speed 3000r\/min).
Rated output: 200W.
Power supply voltage: AC200V.
Serial encoder: 24 bit delta.
Design sequence: C.
Shaft end: straight shaft with keyway, with screw.
Optional parts: with oil seal.
Cantilever state and moment of inertia.
After the change, can still maintain stable action.
Improvement of responsiveness.
Without adjustment, it can be achieved in the past about 2 times the response.
Improvement of stability.
The action is still stable for the presence of load fluctuations.
No gain adjustment.
Zero tuning time to ensure performance.
Protection system from the imppact of temperature anomalies SGMGV-1ED3C2D Setup Rotational Motor Manual SGMGV-1ED3C2D USER'S MANUAL.
Servo unit and servo motor equipped with temperature sensor.
Monitor the temperature of the product directly through the sensor, as soon as possibble to detect and prevent failure SGMGV-1ED3C2D Setup Rotational Motor Manual SGMGV-1ED3C2D USER'S MANUAL.
In addition, the temperature state of the system can be monitored by the machine controller, which is safe and secure