Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGD7S/SGD7W series
>> SGD7S type single axis drive
>> SGD7S-R70A20A | Yaskawa Single axis servo driver SGD7S-R70A20A
SGD7S-R70A20A | Yaskawa Single axis servo driver SGD7S-R70A20A
Yaskawa SGD7S-R70A20A Manual And Instructions
SGD7S-R70A20A datasheetPDF datasheet
SGD7S-R70A20A Communications ReferencesInstallation Guide
SGD7S-R70A20A MECHATROLINK-III CommunicationsINSTRUCTION SHEET
Yaskawa SGD7S-R70A20A Product information and technical parameters：
Brand: Yaskawa
Name: Single axis servo driver
Model: SGD7S-R70A20A
Single axis servo driver SGD7S.
Maximum applicable motor capacity: 0.05kW.
Voltage: three phase AC200V.
Interface: MECHATROLINK-III communication command type. ఼
Design sequence: A.
Hardware purchase pieces: no purchase pieces.
Meet customer specifications required for the 1 products set.
When ordering the servo unit, the parameters set in the factory can be specified.
No need to write parameters in the device assembly site, can reduce the equipment delivery time.
Support product management and maintenance.
After scanning the QR code through the smart phone, it can easily confirm the traceability of the product (production information).
Strengthen trouble shooting
After reading the QR code through the smart phone, the fault diagnosis of the product can be displayed.
Automatic acquisition of tracking information when the servo unit alarm.
Contribute to the failure of the exclusion.
Early monitoring operation, carry out planned maintenance.
Predict the service life of the parts, and prompt the change of time on the screen.
According to the information, in the product before the failure to maintain, in order to prevent the system shutdown
...More relevant models >>>>
SGD7S-R70A20A datasheetPDF datasheet
SGD7S-R70A20A Communications ReferencesInstallation Guide
SGD7S-R70A20A MECHATROLINK-III CommunicationsINSTRUCTION SHEET
Yaskawa SGD7S-R70A20A Product information and technical parameters：
Brand: Yaskawa
Name: Single axis servo driver
Model: SGD7S-R70A20A
Single axis servo driver SGD7S.
Maximum applicable motor capacity: 0.05kW.
Voltage: three phase AC200V.
Interface: MECHATROLINK-III communication command type. ఼
Design sequence: A.
Hardware purchase pieces: no purchase pieces.
Meet customer specifications required for the 1 products set.
When ordering the servo unit, the parameters set in the factory can be specified.
No need to write parameters in the device assembly site, can reduce the equipment delivery time.
Support product management and maintenance.
After scanning the QR code through the smart phone, it can easily confirm the traceability of the product (production information).
Strengthen trouble shooting
After reading the QR code through the smart phone, the fault diagnosis of the product can be displayed.
Automatic acquisition of tracking information when the servo unit alarm.
Contribute to the failure of the exclusion.
Early monitoring operation, carry out planned maintenance.
Predict the service life of the parts, and prompt the change of time on the screen.
According to the information, in the product before the failure to maintain, in order to prevent the system shutdown
SGMCS small capacity type of direct drive servo motor.
Rated torque: M \/ 4.0N.
Servo motor outside diameter size: 230mm.
Serial encoder: 20 bit absolute value type (absolute value of 1 circles) (standard).
Design sequence: the outer diameter of the servo motor is marked as B, C and D.
Flange specification: face C, reverse load side Yaskawa SGD7S-R70A20A.
Optional specifications: no matching.
Under the condition of no speed reducer, the load is directly driven SGD7S-R70A20A
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 6 ~ 600N \/ m, maximum speed: 250 ~ 500r\/min).
By using 20 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping Yaskawa SGD7S-R70A20A.
Use example:
Semiconductor manufacturing equipment.
Liquid crystal circuit board manufacturing equipment.
Various inspection and test equipment.
Electronic part packaging machine.
IC information processor.
IC inspection equipment.
A variety of automated machinery.
Robot。
Small capacity ratings and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above Yaskawa SGD7S-R70A20A.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: A.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP42 (except for the rotating part of the output shaft).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationLow inertia, high speed servo motor type SGM7A (rated speed 3000r\/min).
Rated output: 4.0kw.
Power supply voltage: AC200V.
Serial encoder: 24 bit delta.
Design sequence: A.
Shaft end: straight shaft with keyway, with screw.
Optional parts: with hold brake (DC24V).
Small (about 80% in the past).
Equipped with high-resolution 24bit encoder (16 milllion 770 thousand \/rev pulse) SGD7S-R70A20A.
The maximum torque of 350% (small capacity).
Hope to shorten the working cycle.
Want to improve positioning accuracy.
Increase speed after shaking.
Whether there is no workpiece, action is not stable.
IIt is helpful to the servo performance of ultra high speed and ultra precision control SGD7S-R70A20A. most
To limit the performance of the device to solve the problem
Rated torque: M \/ 4.0N.
Servo motor outside diameter size: 230mm.
Serial encoder: 20 bit absolute value type (absolute value of 1 circles) (standard).
Design sequence: the outer diameter of the servo motor is marked as B, C and D.
Flange specification: face C, reverse load side Yaskawa SGD7S-R70A20A.
Optional specifications: no matching.
Under the condition of no speed reducer, the load is directly driven SGD7S-R70A20A
Can be realized from low speed to high speed of the strong smooth running
(instantaneous maximum torque: 6 ~ 600N \/ m, maximum speed: 250 ~ 500r\/min).
By using 20 bit high resolution encoder, the high precision can be carried out.
The use of hollow structure, convenient wiring and piping Yaskawa SGD7S-R70A20A.
Use example:
Semiconductor manufacturing equipment.
Liquid crystal circuit board manufacturing equipment.
Various inspection and test equipment.
Electronic part packaging machine.
IC information processor.
IC inspection equipment.
A variety of automated machinery.
Robot。
Small capacity ratings and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above Yaskawa SGD7S-R70A20A.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: A.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP42 (except for the rotating part of the output shaft).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationLow inertia, high speed servo motor type SGM7A (rated speed 3000r\/min).
Rated output: 4.0kw.
Power supply voltage: AC200V.
Serial encoder: 24 bit delta.
Design sequence: A.
Shaft end: straight shaft with keyway, with screw.
Optional parts: with hold brake (DC24V).
Small (about 80% in the past).
Equipped with high-resolution 24bit encoder (16 milllion 770 thousand \/rev pulse) SGD7S-R70A20A.
The maximum torque of 350% (small capacity).
Hope to shorten the working cycle.
Want to improve positioning accuracy.
Increase speed after shaking.
Whether there is no workpiece, action is not stable.
IIt is helpful to the servo performance of ultra high speed and ultra precision control SGD7S-R70A20A. most
To limit the performance of the device to solve the problem
...More relevant models >>>>
Last one: Yaskawa Single axis servo driver SGD7S-780A30A002
next one: Yaskawa Single axis servo driver SGD7S-R90A20A
Related download