Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDV type
>> SGMJV type motor
>> SGMJV-01AAA6E | Yaskawa Middle inertia rotary servo motor SGMJV-01AAA6E
SGMJV-01AAA6E | Yaskawa Middle inertia rotary servo motor SGMJV-01AAA6E
Yaskawa SGMJV-01AAA6E Product information and technical parameters：
Brand: Yaskawa
Name: Middle inertia rotary servo motor
Model: SGMJV-01AAA6E
Sigma -V series servo motor SGMJV.
Rated output: 0.1kw (100W).
Power supply voltage: AC200V.
Serial encoder: 13 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal, with the brake (DC24V).
Medium inertia.
Instantaneous maximum torque (rating 350%).
Equipped with a high resolution serial encoder (13\/20 bit).
Max speed up to 6000r\/min.
Variety is complete (50 ~ 750W, with hold brake).
Use example:
Semiconductor manufacturing equipment,
Placement machine,
Punch printed circuit board,
Robot，
Handling machinery，
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Servo motor SGMGH type.
Rated speed: 1500r\/min.
Power: 0.45kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: high precision machine tool.
Shaft end: straight shaft without key.
Optional parts: with oil seal, DC90V brake.
High speed feed series: high speed running when no load Yaskawa SGMJV-01AAA6E.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGMJV-01AAA6E
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlServo driver SGD7S Yaskawa SGMJV-01AAA6E.
Maximum applicable motor capacity: 1.5kW.
Voltage: three phase AC200V.
Interface: MECHATROLINK-II communication command type.
Design sequence: A.
Hardware options: paint.
Performance excellence.
The performance and speed of the device can be improved.
Upgrade free adjustment function.
Without adjusting the operation, no vibration can be achieved Yaskawa SGMJV-01AAA6E.
To ensure that the procedures and parameters of the previous product compatibility.
After replacement of the product, can easily improve the performance of the device.
Sigma -7 series has rich models and related products.
Customers can easily build the system.
From selection to maintenance, rich service content.
Especially when the servo system is in trouble,
Can immediately grasp the product information in the field.
It is helpful to the servo performance of ultra high speed and ultra precision control.
Maximize the performance of the device, to solve the problemLarge capacity SGMVV type servo motor.
Rated output: 22KW.
Voltage: three phase AC200V.
Serial encoder: 20 bit absolute value type.
Rated speed: 800r\/min.
The main mechanical structure: flange type, straight shaft (without keyway and screw).
Optional parts: with hold brake (DC90V), with oil seal.
The use of small, low inertia servo motor, also can give full play to the strength oof the mechanical properties SGMJV-01AAA6E.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusteed, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happen
Rated speed: 1500r\/min.
Power: 0.45kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: high precision machine tool.
Shaft end: straight shaft without key.
Optional parts: with oil seal, DC90V brake.
High speed feed series: high speed running when no load Yaskawa SGMJV-01AAA6E.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain SGMJV-01AAA6E
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlServo driver SGD7S Yaskawa SGMJV-01AAA6E.
Maximum applicable motor capacity: 1.5kW.
Voltage: three phase AC200V.
Interface: MECHATROLINK-II communication command type.
Design sequence: A.
Hardware options: paint.
Performance excellence.
The performance and speed of the device can be improved.
Upgrade free adjustment function.
Without adjusting the operation, no vibration can be achieved Yaskawa SGMJV-01AAA6E.
To ensure that the procedures and parameters of the previous product compatibility.
After replacement of the product, can easily improve the performance of the device.
Sigma -7 series has rich models and related products.
Customers can easily build the system.
From selection to maintenance, rich service content.
Especially when the servo system is in trouble,
Can immediately grasp the product information in the field.
It is helpful to the servo performance of ultra high speed and ultra precision control.
Maximize the performance of the device, to solve the problemLarge capacity SGMVV type servo motor.
Rated output: 22KW.
Voltage: three phase AC200V.
Serial encoder: 20 bit absolute value type.
Rated speed: 800r\/min.
The main mechanical structure: flange type, straight shaft (without keyway and screw).
Optional parts: with hold brake (DC90V), with oil seal.
The use of small, low inertia servo motor, also can give full play to the strength oof the mechanical properties SGMJV-01AAA6E.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusteed, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happen
...More relevant models >>>>
Last one: Yaskawa Middle inertia rotary servo motor SGMJV-A5AAA6E
next one: Yaskawa Middle inertia rotary servo motor SGMJV-C2AAA6E
Related download