Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDV type
>> SGMSV type motor
>> SGMSV-30DDA6D | Yaskawa servo motor SGMSV-30DDA6D
SGMSV-30DDA6D | Yaskawa servo motor SGMSV-30DDA6D
Yaskawa SGMSV-30DDA6D Manual And Instructions
SGMSV-30DDA6D Setup Rotational MotorUSER'S MANUAL
Yaskawa SGMSV-30DDA6D Product information and technical parameters：
Brand: Yaskawa
Name: servo motor
Model: SGMSV-30DDA6D
Sigma -V series servo motor SGMSV.
Rated output: 3.0kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal, with the brake (DC90V).
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
...More relevant models >>>>
SGMSV-30DDA6D Setup Rotational MotorUSER'S MANUAL
Yaskawa SGMSV-30DDA6D Product information and technical parameters：
Brand: Yaskawa
Name: servo motor
Model: SGMSV-30DDA6D
Sigma -V series servo motor SGMSV.
Rated output: 3.0kw.
Power supply voltage: AC400V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal, with the brake (DC90V).
Super power rate.
Variety is complete (1.0kW ~ 7.0kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67 (7.0kw for IP22).
Use example:
Placement machine.
Punch printed circuit board.
Machine tool feeding device.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutes (200V), AC1800V 1 minutes (400V).
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation
Low inertia, high speed servo motor type SGM7A (rated speed 3000r\/min).
Rated output: 2.0kw.
Power supply voltage: AC200V.
Serial encoder: 24 bit delta.
Design sequence: A.
Shaft end: straight shaft with keyway, with screw.
Optional parts: no purchase pieces.
Small (about 80% in the past).
Equipped with high-resolution 24bit encoder (16 million 770 thousand \/rev pulse) Yaskawa SGMSV-30DDA6D.
The maximum torque of 350% (small capacity) SGMSV-30DDA6D
Hope to shorten the working cycle.
Want to improve positioning accuracy.
Increase speed after shaking.
Whether there is no workpiece, action is not stable.
It is helpful to the servo performance of ultra high speed and ultra precision control. most
To limit the performance of the device to solve the problemSigma -v series servo unit SGDV Yaskawa SGMSV-30DDA6D.
Maximum applicable motor capacity: 0.1kw.
Power supply voltage: three phase AC200V.
Design sequence: A type.
Interface: MECHATROLINK- II communication command type (linear servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control Yaskawa SGMSV-30DDA6D. Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.2kw.
Power supply voltage: three phase AC200V.
Design sequence: B type.
Interface: MECHATROLINK- III communication command type (linear servo motor).
Matching (hardware): paint.
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control.
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needds 1,
Pulse generator for D/A converter or position instruction without speed / torque command SGMSV-30DDA6D.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronizzation phase control SGMSV-30DDA6D.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
Rated output: 2.0kw.
Power supply voltage: AC200V.
Serial encoder: 24 bit delta.
Design sequence: A.
Shaft end: straight shaft with keyway, with screw.
Optional parts: no purchase pieces.
Small (about 80% in the past).
Equipped with high-resolution 24bit encoder (16 million 770 thousand \/rev pulse) Yaskawa SGMSV-30DDA6D.
The maximum torque of 350% (small capacity) SGMSV-30DDA6D
Hope to shorten the working cycle.
Want to improve positioning accuracy.
Increase speed after shaking.
Whether there is no workpiece, action is not stable.
It is helpful to the servo performance of ultra high speed and ultra precision control. most
To limit the performance of the device to solve the problemSigma -v series servo unit SGDV Yaskawa SGMSV-30DDA6D.
Maximum applicable motor capacity: 0.1kw.
Power supply voltage: three phase AC200V.
Design sequence: A type.
Interface: MECHATROLINK- II communication command type (linear servo motor).
Matching (hardware): base mounting type (standard).
Realize real time communication.
The maximum transmission speed of 10Mbps and can be set to the communication cycle 250 s ~ 4ms,
Achieved a maximum of 30 stations in the high speed control Yaskawa SGMSV-30DDA6D. Through the high speed of communication,
Can send and receive all kinds of control information in real time.
Energy saving and high efficiency.
A maximum of 30 stations can be connected to the communication lines, can significantly reduce the wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.Sigma -v series servo unit SGDV.
Maximum applicable motor capacity: 0.2kw.
Power supply voltage: three phase AC200V.
Design sequence: B type.
Interface: MECHATROLINK- III communication command type (linear servo motor).
Matching (hardware): paint.
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control.
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needds 1,
Pulse generator for D/A converter or position instruction without speed / torque command SGMSV-30DDA6D.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronizzation phase control SGMSV-30DDA6D.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.
...More relevant models >>>>
Last one: 
next one: Related download