Home
>> Products
>> Yaskawa
>> Servo driver / motor
>> SGDV type
>> Large capacity SGMVV type servo motor
>> SGMVV-3ZDDB2E | Yaskawa Large capacity servo motor SGMVV-3ZDDB2E
SGMVV-3ZDDB2E | Yaskawa Large capacity servo motor SGMVV-3ZDDB2E
Yaskawa SGMVV-3ZDDB2E Product information and technical parameters：
Brand: Yaskawa
Name: Large capacity servo motor
Model: SGMVV-3ZDDB2E
Large capacity SGMVV type servo motor.
Rated output: 30KW.
Voltage: three phase AC400V.
Serial encoder: 20 bit delta.
Rated speed: 1500r\/min.
The main mechanical structure: flange type, straight shaft (without keyway and screw).
Optional parts: with hold brake (DC24V), with oil seal.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties.
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happen
Servo motor SGMGH type.
Rated speed: 1000r\/min.
Power: 0.9kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: B.
Shaft end: taper 1\/10, with parallel key.
Optional parts: with DC24V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain Yaskawa SGMVV-3ZDDB2E SGMVV-3ZDDB2E
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlSecurity module Yaskawa SGMVV-3ZDDB2E.
Maximum applicable motor capacity: 6.0kw.
Power supply voltage: three phase AC400V.
Interface: analog voltage, pulse sequence type (linear servo motor).
Design sequence: A.
Hardware specifications: shelf installation type + paint.
Matching (software): no matching (standard).
Matching (parameters): no matching (standard).
Optional module: security module Yaskawa SGMVV-3ZDDB2E.
European EC standards: Based on the integration of mechanical instructions standard ISO13849-1 EN,
Security module with individual standard 61800-5-2 IEC specified security function.
Through the combination of the SGDV servo unit, the best safety design of the mechanical system is realized.
Suitable for AC servo drive, with the following safety features specified in the international standard IEC61800-5-2 (Japan''s first).
Can easily achieve the best security design of mechanical systems.
Torque Off Safe (STO)
Stop Safe 1 (SS1)
Stop Safe 2 (SS2)
Limited Speed Safely (SLS)
Equipped with 2 security functions, can be set (distribution) security functions.
In addition, the monitoring time and other items can be changed through the parameter.
With the use of the servo unit with a security module, so that the system can be simplified and miniaturized. Sigma -V series servo motor SGMJV.
Rated output: 0.1kw (100W).
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value (standard).
Design sequence: standard.
Shaft end: with two side plane seat (optional).
Optional: with oil seal.
Medium inertia.
Instantaneous maximum torque (rating 350%).
Equipped with a high resolution serial encoder (13/20 bit).
Max speed up to 6000r/min.
Variety is complete (50 ~ 750W, with hold brake).
Use example:
Semiconductor manufacturing equipment,
Placement machine,
Punch printed circuit board,
Robot，
Handling machinery，
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Insstallation method: flange type SGMVV-3ZDDB2E.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew) SGMVV-3ZDDB2E.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation.
Rated speed: 1000r\/min.
Power: 0.9kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: B.
Shaft end: taper 1\/10, with parallel key.
Optional parts: with DC24V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain Yaskawa SGMVV-3ZDDB2E SGMVV-3ZDDB2E
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlSecurity module Yaskawa SGMVV-3ZDDB2E.
Maximum applicable motor capacity: 6.0kw.
Power supply voltage: three phase AC400V.
Interface: analog voltage, pulse sequence type (linear servo motor).
Design sequence: A.
Hardware specifications: shelf installation type + paint.
Matching (software): no matching (standard).
Matching (parameters): no matching (standard).
Optional module: security module Yaskawa SGMVV-3ZDDB2E.
European EC standards: Based on the integration of mechanical instructions standard ISO13849-1 EN,
Security module with individual standard 61800-5-2 IEC specified security function.
Through the combination of the SGDV servo unit, the best safety design of the mechanical system is realized.
Suitable for AC servo drive, with the following safety features specified in the international standard IEC61800-5-2 (Japan''s first).
Can easily achieve the best security design of mechanical systems.
Torque Off Safe (STO)
Stop Safe 1 (SS1)
Stop Safe 2 (SS2)
Limited Speed Safely (SLS)
Equipped with 2 security functions, can be set (distribution) security functions.
In addition, the monitoring time and other items can be changed through the parameter.
With the use of the servo unit with a security module, so that the system can be simplified and miniaturized. Sigma -V series servo motor SGMJV.
Rated output: 0.1kw (100W).
Power supply voltage: AC200V.
Serial encoder: 20 bit absolute value (standard).
Design sequence: standard.
Shaft end: with two side plane seat (optional).
Optional: with oil seal.
Medium inertia.
Instantaneous maximum torque (rating 350%).
Equipped with a high resolution serial encoder (13/20 bit).
Max speed up to 6000r/min.
Variety is complete (50 ~ 750W, with hold brake).
Use example:
Semiconductor manufacturing equipment,
Placement machine,
Punch printed circuit board,
Robot，
Handling machinery，
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Insstallation method: flange type SGMVV-3ZDDB2E.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V 1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew) SGMVV-3ZDDB2E.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation.
...More relevant models >>>>
Last one: Yaskawa Large capacity servo motor SGMVV-2BDDB2E
next one: Yaskawa Large capacity servo motor SGMVV-3GDDB2E
Related download