Yaskawa SGD7S-R70A10A001 MECHATROLINK-II Communications Manual SGD7S-R70A10A001 INSTRUCTION SHEET

Sigma -V series servo motor SGMAV.
Rated output: 0.05kw (50W).
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: standard.
Shaft end: straight shaft with keyway, with screw (optional).
Optional: with oil seal.
Super power rate.
Small capacity.
Ultra low inertia
Instantaneous maximum torque (rating 300%) SGD7S-R70A10A001 MECHATROLINK-II Communications Manual SGD7S-R70A10A001 INSTRUCTION SHEET SGD7S-R70A10A001
Equipped with a high resolution serial encoder (20 bit).
Max speed up to 6000r\/min.
Variety is complete (50W ~ 1.0kw, with hold brake).
Use example:
Semiconductor manufacturing equipment,
Placement machine,
Punch printed circuit board,
Robot，
Handling machinery，
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15 SGD7S-R70A10A001 MECHATROLINK-II Communications Manual SGD7S-R70A10A001 INSTRUCTION SHEET.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: B.
Insulation withstand voltage: AC1500V1 minutes.
Protection mode: fully enclosed self cooling type IP65 (except shaft through part).
The use of environmental humidity: 20 ~ 80% (not dew).
Connection mode: direct connection SGD7S-R70A10A001 MECHATROLINK-II Communications Manual SGD7S-R70A10A001 INSTRUCTION SHEET.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotationServo motor SGMGH type.
Rated speed: 1000r\/min.
Power: 2.0kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: high precision machine tool.
Shaft end: straight shaft with screw key.
Optional parts: with oil seal, DC90V brake.
High speed feed series: high speed running when no load.
Complete separation of the main circuit and the control circuit,
Alarm can only turn off the main circuit power supply, easy to maintain.
Parameter setting device.
The parameters can be directly entered by the servo drive body.
Saving wiring.
Using a serial encoder, encoder wiring number than the original product reduced by 1\/2.
Multi in one control: the use of the parameters of the switch can not use the torque, position, speed controlServo motor SGMDH type.
Rated speed: 3000r\/min.
Power: 2.2kw.
Power supply voltage: three phase AC200V.
Serial encoder: 17 bit absolute value.
Design sequence: A.
Shaft end: straight shaft without key.
Optional parts: with oil seal, D90V brake.
Partial flat series: the need to install the servo motor in a small space.
Rich motor series.
Equipped with brake, belt reducer, such as a wealth of motor products.
Online automatic adjustment, automatic measurement of mechanical properties, set the required servo gain.
Even if the initial contact, can also be completed in a short time the best set.
Automatic iidentification of the motor, servo drive automatic identification of servo motor power, specifications, automatic setting motor parameters SGD7S-R70A10A001 MECHATROLINK-II Communications Manual SGD7S-R70A10A001 INSTRUCTION SHEET.
Standard for regeneerative resistance connection terminals SGD7S-R70A10A001 MECHATROLINK-II Communications Manual SGD7S-R70A10A001 INSTRUCTION SHEET.
Connecting terminal equipped with external regenerative resistance,
Convenient connection regenerative resistor