Yaskawa SGDV-5R4D11A020FT003 Design and Maintenance Manual SGDV-5R4D11A020FT003 USER'S MANUAL

Large capacity SGMVV type servo motor.
Rated output: 22KW.
Voltage: three phase AC200V.
Serial encoder: 20 bit absolute value type.
Rated speed: 1500r\/min.
The main mechanical structure: support mounting type, straight shaft (with keyway and screw).
Optional parts: do not buy pieces.
The use of small, low inertia servo motor, also can give full play to the strength of the mechanical properties SGDV-5R4D11A020FT003 Design and Maintenance Manual SGDV-5R4D11A020FT003 USER'S MANUAL SGDV-5R4D11A020FT003
The new model SGMVV with a rated output of 22~55KW, the amount of passenger speed 800r\/min and 1500r\/min products.
After the motor is installed, the phase is started to run immediately.
Even if the servo is not adjusted, as long as the moment of inertia is within the allowable range,
Even if the load changes, it can be driven stably, and the vibration will not happenSigma -v series servo unit SGDV SGDV-5R4D11A020FT003 Design and Maintenance Manual SGDV-5R4D11A020FT003 USER'S MANUAL.
Maximum applicable motor capacity: 1kw.
Power supply voltage: three phase AC200V.
Design sequence: B type.
Interface: MECHATROLINK- III communication command type (linear servo motor).
Matching (hardware): paint.
Realize real time communication
With the maximum transmission speed of 100Mbps and the set of communication cycle 125S ~ 4ms, to achieve a more than 62 stations of the high speed control SGDV-5R4D11A020FT003 Design and Maintenance Manual SGDV-5R4D11A020FT003 USER'S MANUAL.
Through the high speed of communication, can send and receive all kinds of control information in real time.
Contribute to cost savings
A maximum of 62 stations can be connected to the communication line, can significantly reduce wiring costs and time.
The command connector of the upper controller only needs 1,
Pulse generator for D/A converter or position instruction without speed / torque command.
High precision motion control is realized.
In addition to torque, position and speed control, but also to achieve high precision synchronization phase control.
Because the control mode can be switched on line, the complicated mechanical action can be realized more effectively and smoothly.Sigma -V series servo motor SGMGV.
Rated output: 5.5kw.
Power supply voltage: AC200V.
Serial encoder: 20 bit Delta (standard).
Design sequence: Standard (bolt for silver).
Shaft end: straight shaft, without keyway (standard).
Optional: with oil seal.
A variety of mechanical feed shaft drive (high speed feed).
Variety is complete (300W ~ 15kW, with hold brake).
Equipped with a high resolution serial encoder (20 bit).
Standard using IP67.
Use example:
Machine tool。
Transport machinery.
Handling machinery。
Food processing machinery.
Rating and specifications:
Rated time: continuous.
Vibration level: V15.
Insulation resistance: DC500V, 10M, or above.
Using ambient temperature: 0 ~ 40 degrees C.
Excitation mode: permanent magnet type.
Installation method: flange type.
Heat resistance grade: F.
Insulation withstand voltage: AC1500V 1 minutess (200V), AC1800V 1 minutes (400V) SGDV-5R4D11A020FT003 Design and Maintenance Manual SGDV-5R4D11A020FT003 USER'S MANUAL.
Protection mode: fully enclosed self cooling type IP67 (except shaft through part).
The use of environmental humidity: 20 ~ 80%% (not dew) SGDV-5R4D11A020FT003 Design and Maintenance Manual SGDV-5R4D11A020FT003 USER'S MANUAL.
Connection mode: direct connection.
Rotation direction: clockwise direction (CCW) rotation at the load side under the direction of rotation